Home > Error Code > Whirlpool Oven Error Codes

Whirlpool Oven Error Codes

Contents

If during one wash cycle 4 undervoltages occur then a Motor Control Unit failure is displayed. 1. Check that NTC resistance of the Steamer is in range between 170 kΩ and 300 Ω, refer to Temperature Sensor table on page 10. Check for loose connectors. 3. Replace is defective. Source

If door not latched: Disconnect power from unit. Disconnect power for at least 30 seconds.2. Quick Question! If code re-appears, replace the control board (also called ERC or clock).If you need further help or clarification on this answer, please do not hesitate to reply to this post.Thanks for

Whirlpool Oven Error Codes

F4 - Shorted Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD). For SELF CLEAN models: check door lock operation. 3. Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab. Check/clean drain pump filter of foreign objects. 5.

Replace failed component. F3 - Open Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD). Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU). Whirlpool Top Load Washer Error Codes Ask a Technician for Answers ASAP Ask an Expert Home Improvement Questions Appliance Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help

Replace failed component. Make sure all grounding switches are engaged. 3. Opening the lid will allow you to view and redistribute the load. http://www.justanswer.com/appliance/1hvff-does-code-f1e2-digital-display-mean-oven.html Note: Unit will attempt to unlock itself during this error six times before displaying this error code.

Check for conformal coating on serial communication pins between the machine controller and the motor controller. Whirlpool Microwave Error Codes Check door switch/lock unit. 3. Remove the lower toe panel. 3. Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller.

Whirlpool Range Error Code F9e0

If damage is found, replace appropriate part. F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. Whirlpool Oven Error Codes F23 HEATER FAILURE If the temperature increase during the first 40 minutes is less than 86°F (30°C). 1. Whirlpool Washing Machine Error Codes E1 F7 - E1 Common switch wire is defective Common wire (+5VDC) to latch switch, and to door switch is shorted to chassis ground or neutral.

Failure Code LED Status Duet Sport LED Status Duet Sport HT F01 Add a Garment Add a Garment F11 Add a Garment, Wash, Spin Add a Garment, Soak/Prewash, Rinse F20 Rinse, this contact form CE - Communication Error - Disconnect power and unplug unit. The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Whirlpool Range F9 Error Code

  • Check the MCU by looking for operations of the drive motor. 7.
  • ob - Off Balance - The lid switch must be opened at least once before reseting the cycle.
  • Unplug washer or disconnect power. 4.
  • Sud SUDS LOCK (Overdose of detergent detected during the wash cycle) The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor.
  • F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted.
  • Press 'Stop/Cancel' to clear display.
  • Whirpool Duet Front Loading Automatic Washer Fault Codes FH - Detects No Water Entering Machine or No Pressure Switch Trip - Select 'cancel' twice to clear this code.

If code re-appears, replace control board (also called ERC or clock). Sounds like my original board may be fine; all three (including two new boards) can't be defective. Make sure your control board is the correct one. http://fullflash.net/error-code/vpn-error-codes.html If corrections are made in any step, reconnect power to control.

Check connections of the CCU board within the housing. Whirlpool Accubake Oven Error Codes Potential Causes • Check the Water Temperature Sensor, Heating Element and Element Relay • Check connections to the Sensor, Heating Element and Relay Replace failed component. F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times.

Potential Causes • Check wire harness connections between the Drive Motor/Tachometer and the Motor ControlUnit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the Drive Motor

Check keypad connector for firm connection (keypad connects to control board). 2. D. Measure sensor value (between connector pins) between 1000 ° @ 900 F (room temperature approx. = 1080 real temperature, disconnect power, replace sensor and refer to steps 3-5. Whirlpool Top Load Washing Machine Error Codes F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle.

Press CANCEL PROGRAM and start the clean mode, and observe for one minute to ensure that operation is normal. 1. Mismatch of User Interface and CCU or corrupted EEPROM. 1. Disconnect power for at least 30 seconds. 2. Check This Out LF - Long Fill - If the water fill time exceeds ten minutes, the water valves will be shut off and this error code will display.

F09 - Overflow Condition (Pressure Switch Closed Too Long) - Check to make sure drain hose is not plugged or kinked and unplug the unit and disconnect power. Press 'Stop/Cancel' to clear display. If door latched: Disconnect power from unit. Check wires and connectors from control to door switch, then from door switch to control.

Can you tell me the part number for the control board?Thanks again, Lee Expert: Brian replied8 years ago. Press PAUSE/CANCEL twice to clear the display. If you can’t look through it, exchange Steamer. 5. Unplug washer or disconnect power. 2.

Check the drain hose and make sure it is not plugged or kinked. 2. Verify pressure switch operation. 7. Unplug washer or disconnect power. 8. F11 Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.

Potential Causes • If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent. This should have AC line voltage when the motor controller is powered. Check all connections at control board and at the latch switch and door switch. Door not opened during 3 consecutive cycles. 1.

Unplug washer or disconnect power. 3. If there is water in the unit, verify the drain pump is working and the pressure switch hose is in good condition and properly connected. If a failure occurs during high-speed spin, the door unlocks after 3 minutes. 1.