Home > Unexpected Error > Unexpected Error 10051 From Winsock

Unexpected Error 10051 From Winsock

WinSock description: No equivalent. BR Ole If you would like to refer to this comment somewhere else in this project, copy and paste the following link: SourceForge About Site Status @sfnet_ops Powered by Apache Allura™ Return code/valueDescription WSA_INVALID_HANDLE 6 Specified event object handle is invalid. This is not a software error, another type of name server request may be successful. this contact form

WSAEUSERS 10068 User quota exceeded. There are only a few possible causes for this error: you tried to connect to the wrong port. WSAETOOMANYREFS 10059 Too many references. Public Group, 2625 members Primary Navigation ConversationsPhotosFilesAttachmentsEventsPollsLinksDatabaseAbout More Secondary NavigationHelpAttachmentsEventsPollsLinksDatabaseAboutEdit Membership Back View NextPreviousFixed Width FontView Source8215Re: [blat] Error in Blat : "unexpected error 10051 from winsock"Expand MessagesTim MussonFeb 3, 2006 great post to read

WSA_QOS_EFILTERSTYLE 11019 Invalid QoS filter style. Check the destination address you are using. Winsock description: Winsock doesn't support the sendmsg() function, and some Winsock implementations are not so strict as to require an application with a datagram socket to 'disconnect'--by calling connect with a This is a generic error code, returned under various conditions.

User suggestions: Check the obvious first: check that the destination address is a valid IP address. Discussion of BLAT. Usually the manufacturer of the device or software will also have specific instructions available on their Web site. This error occurs if you specifically reference a protocol that isn't part of the address family you also reference.

The ICMP message means that the router can't forward the IP datagram, possibly because it didn't get a response to the ARP request (which might mean the destination host is down). The requested service provider could not be loaded or initialized. The "address" it refers to is the remote socket name (protocol, port and address). This error occurs when the sin_port value is zero in a sockaddr_in structure for connect() or sendto().

Although some WinSock implementations might not issue other errors if a connection fails, so you can handle this error as you would others that indicate connection failure. Alternately, you could call getprotobyname() or WSAAsyncGetProtoByName() to get the appropriate protocol value from the network system. If using a local server table for server name resolution, check to see that it doesn't resolve to an obsolete address. On the main menu, click File > Properties.

Switch to the opposite data connection type (PASV or PORT) under Site Settings > Type tab. https://beta.groups.yahoo.com/neo/groups/blat/conversations/messages/8215 WSANO_DATA (11004)* Valid name, no data record of requested type The requested name is valid, but does not have an Internet IP address at the name server. We suggest local configuration changes that might remedy the problem, and network and server conditions that might be the cause. Try pinging the address. (See Troubleshooting Tips for details.) If you are using a router, verify the router is up and running (check by pinging it and then ping an address

This usually results from trying to connect to a service that is inactive on the foreign host—that is, one with no server application running. weblink WinSock functions: gethostbyaddr(), gethostbyname(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), See also: WSAHOST_NOT_FOUND, WSANO_RECOVERY, WSATRY_AGAIN WSANO_RECOVERY (11003) This is a non-recoverable error Berkeley description: This is a WSA_IO_INCOMPLETE 996 Overlapped I/O event object not in signaled state. The ICMP message means that a router cannot forward the IP datagram, possibly because it did not get a response to an ARP request (which might mean the destination host is

WinSock description: Same as Berkeley for host resolution. This won't reveal too much unless you know the router addresses at the remote end, but it might help to identify if the problem is somewhere along the way. It could also occur if an application opens and closes sockets often, but doesn't properly close the sockets (so it leaves them open, as "orphans"). http://fullflash.net/unexpected-error/timed-out-if-winsock-dll-error-10060.html The Windows Sockets API provides access to 'low-level' APIs (like the transport protocols TCP and UDP), so this error is not relevant to Winsock.

In this case, the 2nd application will fail with WSAEADDRINUSE. The Windows function is indicating a problem with one or more parameters. It would also timeout if a (FIN)ish TCP packet is not ACK'd (and even if the FIN is ACK'd, it will eventually timeout if a FIN is not returned).

I already download the winsock to repair the erro in winsock, b> unfortunately I failed to fix the problem -- Tim Musson Flying with The Bat!

  • WSAHOST_NOT_FOUND for details.WSANO_ADDRESS (11004)* No address, look for MX record The requested name is valid, but does not have an Internet IP address at the name server.
  • The errors that have User suggestions are all the same ones in the "User-fixable errors" list above.
  • Too many references to some kernel object.
  • WSAECONNRESET (10054) Connection reset by peer A connection was forcibly closed by a peer.
  • A retry at some time later may be successful.
  • Some of these neglected error values are among those mentioned earlier that provide "finer resolution" on different WinSock implementations.
  • User suggestions: see WSAHOST_NOT_FOUND for details.
  • The standard meaning for WSAEINVAL applies to connect() (invalid argument).
  • WSA_QOS_BAD_OBJECT 11013 QoS bad object.
  • connect(), send(), recv(), et cetera).

No process may have more than a system-defined number of file descriptors open at a time. It's also possible that the local services file has an incorrect port number (although it's unlikely). Test Email - Result is "Error" b> Blat -t [email protected] -attach d:\temp\cell.txt -subject b> MySubjectName b> This are the error i got after I run the "Test Mail" b> Sending stdin.txt This error also could occur if an application opens and closes sockets often, but doesn't properly close the sockets (so it leaves them open, as 'orphans').

WSAEREFUSED 10112 Database query was refused. Berkeley description: A directory with entries other than `.'and `..' was supplied to a remove directory or rename call. WinSock functions: With a datastream socket: connect() and FD_CONNECT WSAAsyncelect() notification message. his comment is here Usually, the manufacturer of the device or software has specific instructions available on their Web site.